A.) show IOS
B.) show ver
C.) show flash
D.) show mem
E.) show NVRAM
Ans B C
502 Identify the command to copy a configuration file from a TFTP server to a routers
active configuration?
A.) Router# copy running-config tftp
B.) Router# copy tftp running-config
C.) Router# copy tftp 172.16.0.1 running-config
D.) Router(config)# copy tftp running-config
Ans D
503 Identify the command mode necessary to enter the extended ping command?
A.) Router#
B.) Router>
C.) Router(config)#
D.) Router(ext-ping)#
Ans A
504 Identify the command to configure the router for IGRP autonomous system 100?
A.) Router(config)# router igrp 100
B.) Router> router igrp 100
C.) Router# router igrp 100
D.) Router(config)# router igrp
Ans A
505 Identify the command that forces the router to load into ROM mode upon a reload?
A.) boot system rom
B.) rom boot
C.) boot system flash rom
D.) boot router rom
Ans A
506 Identify the command that specifies Serial 0 in slot 1?
A.) Router(config)# interface serial1/1
B.) Router(config)# interface serial1/0
C.) Router(config)# interface serial0.1
D.) Router(config)# interface serial0/1
Ans B 507 Identify the command to configure the configuration-register?
A.) Router# config-register 0x2102
B.) Router(config)# config-register 0x2102
C.) Router(config-reg)# 0x2102
D.) Router> config-register 0x2102
Ans B
508 Identify the command to disable CDP on an interface?
A.) Router(config-if)# no cdp enable
B.) Router(config-if)# no cdp run
C.) Router# no cdp enable
D.) Router(config-if)# no cdp
Ans A
509 Identify the command that will display the RIP routes entering and leaving the router?
A.) Router(config)# debug ip rip
B.) Route# debug ip rip
C.) Router>debug ip rip
D.) Router# debug rip routes
Ans B
510Identify the prompt displayed if in privileged exec mode?
A.) Router(config)#
B.) Router#
C.) Router>
D.) Router(priv)#
Ans B
CCNA Interview Questions Page 51
<<Previous Next>>
511 'Show cdp neighbors detail' show the following 3 pieces of information?
A.) Hardware platform
B.) Software version
C.) Same as 'show version' command
D.) Up to 1 address for each protocol
E.) Non-direct connected routers
Ans A B D
512 Identify the command mode necessary to enter the standard ping command?
A.) Router(config)#
B.) Router>
C.) Router(std-ping)#
D.) Router(config-if)# Ans B
513 Identify the command to run 'setup'?
A.) Router(config)#setup
B.) Router?setup
C.) Router#setup
D.) Router>setup
Ans C
514 Identify the command that configures serial0 for PPP encapsulation?
A.) Router(config)# encapsulation ppp
B.) Router(config-if)# encapsulation serial ppp
C.) Router(config-if)# encapsulation ppp
D.) Router# encapsulation ppp
Ans C
515 Identify the command to display the status of the Frame Relay virtual circuit?
A.) Router# show frame-relay virtual-circuit
B.) Router(config)# show frame-relay pvc
C.) Router# show frame-relay pvc
D.) Router# show virtual
Ans C
516 Identify the command that disables name-to-address translation?
A.) Router(config-dns)# no ip domain-lookup
B.) Router(config)# no address translation
C.) Router(config)# no ip domain-lookup
D.) Router(config)# ip domain-lookup
Ans C
517 What command will not display the status of to1?
A.) show int to1
B.) show to1
C.) show interface to1
D.) show interface
Ans B
518 Identify the 2 commands to copy a configuration from a TFTP server to RAM?
A.) configure network
B.) configure overwrite
C.) copy backup-config running-config
D.) copy tftp running-config
Ans A D 519 Identify the following command to configure a secret password to 'cisco'?
A.) Router(config)#enable password cisco secret
B.) Router(config)#enable secret cisco
C.) Router(config)#enable secret password cisco
D.) Router(config)#set secret = cisco
Ans B
520Identify the effect of Ctrl-Z?
A.) Exits back to privileged exec mode
B.) Disconnect from the router
C.) Abort the ping operation
D.) Exits privileged exec mode
Ans A
CCNA Interview Questions Page 52
<<Previous Next>>
521 Given an IPX network with redundant paths, what command will configure load
balancing?
A.) ipx load-balance
B.) ip maximum-paths 2
C.) ipx maximum-paths 2
D.) ipx load-share
Ans C
522 Identify the correct IGRP configuration?
A.) Router# router igrp 100
Router# network 10.0.0.0
B.) Router(config)# router igrp 100
Router(config-router)# network 10.0.0.0
C.) Router(config)# router igrp
Router(config-router)# network 10.0.0.0
Ans B
523 Identify the components in the following command 'interface serial0/1/1'
A.) Serial interface, port number 0, slot 1, port adapter 1
B.) Serial interface, slot 1, port number 1, port adapter 0
C.) Serial interface, slot 0, port adapter 1, port number 1
Ans C
524 Identify the command to view the configuration-register value?
A.) show register
B.) display config-register
C.) show config D.) show version
Ans D
525 Identify the 2 commands that save the running-config to a TFTP server?
A.) write running tftp
B.) copy running network
C.) copy running tftp
D.) write network
Ans C D
526 Identify the mode reflected by the following prompt 'Router<boot>'?
A.) Setup
B.) RXBoot
C.) Boot mode
D.) Privileged exec mode
Ans B
527 How do you disable CDP on the entire Router?
A.) Router#no cdp run
B.) Router(config-if)# no cdp enable
C.) Router(config)# no cdp enable
D.) Router(config)# no cdp run
Ans D
528 What command can be used to test IPX connectivity?
A.) Ping 2e.000.0045.8923
B.) Ping 192.168.100.1
C.) Ping ipx 2e.0000.0045.8923
D.) Ipx ping 2e.0000.0045.8923
Ans D
529 Identify the 2 commands that display the clock rate configured on the serial0
interface?
A.) show serial0
B.) show interface serial0
C.) Show clock rate serial 0
D.) show controllers serial 0
E.) show running-config
Ans B D
530 What is the command to copy the IOS image to a TFTP server?
A.) copy flash tftp
B.) copy running-config tftp
C.) copy ios tftp D.) copy startup-config tftp
Ans A
CCNA Interview Questions Page 53
<<Previous Next>>
531 Identify the command that configures the bandwidth to 56K?
A.) Router(config-if)# bandwidth 56000
B.) Router(config-if)# bandwidth 56k
C.) Router(config)# bandwidth 56
D.) Router(config-if)# bandwidth 56
Ans D
532 Identify the command to configure DLCI 100 on an interface e0?
A.) Router(config)# frame-relay local-dlci 100
B.) Router(config)# frame-relay local-dlci 100 int e0
C.) Router(config-if)# frame-relay local-dlci 100
D.) Router(config-if)# frame-relay local-dlci 100 int e0
Ans C
533 Identify the command to configure the router to boot from an alternate IOS located in
flash?
A.) boot system flash IOS.exe
B.) boot system tftp IOS.exe 172.16.5.1
C.) boot system alternate IOS.exe
D.) boot system rom IOS.exe
Ans A
534 Identify the command to configure a description on an interface?
A.) Router> description Finance department
B.) Router(config)# description Finance department
C.) Router(config-if)# description Finance department
D.) Router# description Finance department
Ans C
535 Identify the 2 commands that will display the status and information about interface E0
only?
A.) show interface ethernet E0
B.) show interface E0
C.) show E0
D.) show int E0
E.) show interface
Ans B D 536 In order to configure a Frame Relay subinterface with IP identify the 2 commands that
must be configured on the physical interface?
A.) Router(config-if)# encapsulation frame-relay
B.) Router(config-if)# no ip address
C.) Router(config-if)#encapsulation subinterface frame-relay
D.) Router(config)# subinterface s0 encapsulation frame-relay
Ans A B
537 Identify the command to determine if an IP access-list is grouped on interface e0?
A.) Router(config)# show ip interface e0
B.) Router> show ip interface e0
C.) Router# show interface e0
D.) Router# show ip interface e0
Ans C
538 Identify the keystroke to position the cursor to the beginning of a command line?
A.) Ctrl-A
B.) Ctrl-Ins
C.) Ctrl-B
D.) Ctrl-Z
Ans A
539 Identify the following components of the IPX address 2e.0000.0065.ed43
A.) Not a valid IPX address
B.) Network = 2e, Subnet = 0000, Node = 0065.ed43
C.) Network = 2e.0000, Node = 0065.ed43
D.) Network = 2e, Node = 0000.0065.ed43
Ans D
540 What is the syntax to add a banner to the Cisco router?
A.) motd banner #
B.) banner
C.) banner motd #
D.) banner #
Ans C
CCNA Interview Questions Page 54
<<Previous Next>>
541 What is the command to allow you to type Tokyo instead of the IP address 172.16.30.1
to access a router named Tokyo?
A.) config t, ip host Tokyo 172.16.30.1
B.) config t, ip hostname Tokyo 172.16.30.1
C.) config t, hostname Tokyo 172.16.30.1 D.) config t, ip hostname 172.16.30.1 Tokyo
Ans A
542 How do you disable advanced editing?
A.) terminal editing
B.) terminal no editing
C.) disable editing
D.) no terminal editing
Ans B
543 Which of the following will show an extended access list 150?
A.) sh access-list 150
B.) sh ip int
C.) sh ip access-list
D.) sh access-list 150 extended
Ans A C
544 You have a Class B network address divided into 30 subnets. You will add 25 new
subnets within the next year. You need 600 host IDs for each subnet. Which subnet mask
should you use?
A.) 255.254.0.0
B.) 255.192.0.0
C.) 255.255.252.0
D.) 255.255.248 0
Ans C
545What is the syntax to use to configure the port on a Catalyst 5000 switch?
A.) slot port/type
B.) type slot/port
C.) port slot/type
D.) port type/slot
546 What 3 sources can configuration commands be placed into RAM?
A.) HP Openview
B.) Console
C.) Vterminal
D.) TFTP server
E.) NVRAM
Ans B D E
547 Identify the true statements about the following access list:
Access-list 101 deny tcp 192.10.172.0 0.0.0.255 any eq 23
Access-list 101 permit ip any any
A.) This access list prevents the host 192.10.172.0 from telneting
B.) This access list prevents any telnet traffic from subnet 192.10.172.0/24 C.) This access list filters some telnet access
D.) This access list denies any telnet traffic to subnet 192.10.172.0/24
E.) This access list is invalid
F.) The netmask on the this access list is reversed
Ans B C
548 Given the IPX address 4a.0002.1111.a999, what is the network ID and what is the node
ID?
A.) net 4a host 0002.1111.a999
B.) net a999 node 0002.1111
C.) net 0002.1111.a999 node 4a
D.) net 0002.1111 node a999
Ans A
549 What command do you use to disable domain lookup?
A.) no domain-lookup
B.) domain no-lookup
C.) lookup no-domain
D.) no ip domain-lookup
Ans D
550 Which of the following are valid Cisco encapsulation type names?
A.) arpa = IPX Ethernet
B.) novell-ether = IPX Ethernet_802.3
C.) snap = IEEE 802.2 SNAP on Ethernet, FDDI, and Token Ring
D.) novell-fddi = IPX Fddi_Raw
E.) sap = IEEE 802.2 on Ethernet, FDDI, and Token Ring
F.) hdlc = HDLC on serial interfaces
Ans B C E F
Author Name
Author Description!
Get Free Email Updates to your Inbox!
Post a Comment